| ▶ 배선기구류 |
| IEC 60947-1:2020 |
Low-voltage switchgear and controlgear - Part 1: General rules
(Exception)
Annex C Degrees of protection of enclosed equipment |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| IEC 60947-2:2019 |
Low-voltage switchgear and controlgear - Part 2: Circuit-breakers |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| IEC 60947-2:2024 |
Low-voltage switchgear and controlgear - Part 2: Circuit-breakers |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| K 60947-1:2011 |
저압 개폐장치 및 제어장치 제 1 부 : 일반규정
(Exception)
부속서 C 폐쇄된 기기의 보호 등급 |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| K 61009-1:2011 |
가정용 및 이와 유사한 용도의 과전류 보호장치를 가진 누전차단기(RCBO) 제1부:일반 요구사항 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KC 60947-2:2022 |
저압 개폐장치 및 제어장치 제 2 부 : 차단기 |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| KC 60947-4-1:2015 |
저전압 개폐장치 및 제어장치 제4-1부 : 접촉기 및 모터기동기 - 전자식 접촉기 및 모터기동기 |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| KC 60947-5-1:2016 |
저압개폐장치 및 제어장치 제5-1부 : 제어회로 소자 및 개폐소자 - 전기기계적 제어회로 소자 |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| KC 60898-1:2015 |
가정용 및 이와 유사한 용도의 과전류 보호용 차단기 제1부:교류용 차단기 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KC 61008-1:2015 |
가정용 및 이와 유사한 용도의 과전류 보호장치가 없는 누전차단기(RCCB) 제1부: 일반 요구사항 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| UL 508:2018 |
Industrial Control Equipment
Part II: Magnetic motor controller
Part III: Manual motor controller
Part IV: Combination motor controller
Part X: Auxiliary devices
Part XI: Mechanical overload relays
Part XIII: Definite purpose controllers |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| UL 508:2024 |
Industrial Control Equipment
Part II: Magnetic motor controller
Part III: Manual motor controller
Part IV: Combination motor controller
Part X: Auxiliary devices
Part XI: Mechanical overload relays
Part XIII: Definite purpose controllers |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| UL 489:2019 |
Molded-case Circuit Breakers, Molded-Case Switches and Circuit-Breaker Enclosures
7.1.2.2 200 percent calibration at 25 ℃(77 ℉)
7.1.2.3 135 percent calibration at 25 ℃(77 ℉)
7.1.2.2 200 percent calibration at 40 ℃(104 ℉)
7.1.2.3 135 percent calibration at 40 ℃(104 ℉)
7.1.2.4 100 percent calibration at 40 ℃(104 ℉)
7.1.2.4 Temperature and 100 percent calibration at 25 ℃(77 ℉)
7.1.2.5 Calibration of adjustable instantaneous trip
7.1.3 Overload
7.1.5 Endurance
7.1.6 200 percent calibration at 25 ℃, repeated
7.1.6 135 percent calibration at 25 ℃, repeated
7.1.6 135 percent calibration at 40 ℃(104 ℉), repeated
(Exception)
Other clauses |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| KS C IEC 61009-1:2013 |
주택용 및 이와 유사한 용도의 과전류 보호장치를 가진 누전차단기(RCBO)－제1부: 일반 요구사항 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KS C IEC 61009-2-1:1991 |
주택용 및 이와 유사한 용도의 과전류 보호장치를 가진 누전차단기(RCBO) — 제2-1부: 회로전압 독립형 RCBO에 대한 일반 요구사항의 적용 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KS C IEC 61009-2-2:2014 |
주택용 및 이와 유사한 용도의 과전류 보호장치를 가진 누전차단기(RCBO) — 제2-2부: 회로전압 의존형 RCBO에 대한 일반 요구사항의 적용 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KS C IEC 61008-1:2013 |
주택용 및 이와 유사한 용도의 과전류 보호장치가 없는 누전차단기(RCCB)－제1부: 일반 요구사항 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KS C IEC 61008-2-1:1990 |
주택용 및 이와 유사한 용도의 과전류 보호장치가 없는 누전차단기(RCCB) — 제2-1부: 회로전압 독립형 RCCB에 대한 일반 요구사항의 적용 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KS C IEC 61008-2-2:1990 |
주택용 및 이와 유사한 용도의 과전류 보호장치가 없는 누전차단기(RCCB) — 제2-2부: 회로전압 의존형 RCCB에 대한 일반 요구사항의 적용 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KS C IEC 60898-1:2019 |
주택용 및 이와 유사한 용도의 과전류 보호용차단기 - 제1부: 교류용 차단기 |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| KS C IEC 60947-5-1:2009 |
저압개폐장치 및 제어장치－제5-1부: 제어회로 소자 및 개폐 소자－전기기계적 제어회로 소자 |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| KS C IEC 60947-4-1:2018 |
저전압 개폐 장치 및 제어 장치－제4-1부: 접촉기 및 모터 기동기－전자식 접촉기 및 모터 기동기 |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| KS C IEC 60947-2:2019 |
저전압 개폐장치 및 제어장치 - 제2부 : 차단기 |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| KS C IEC 60947-1:2014 |
저전압 개폐장치 및 제어장치 - 제1부 : 일반 규정
(Exception)
부속서 C 외함 내에서 사용하는 기기의 보호 등급 |
순시특성 시험: AC 200 kA & DC 100 kA
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| IEC 61009-1:2013 |
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) - Part 1: General rules |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 61009-1:2024 |
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) - Part 1: General rules |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 61009-2-1:2024 |
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO's) - Part 2-1: Applicability of the general rules to RCBO's functionally independent of line voltage |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 61009-2-2:2024 |
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO's) - Part 2-2: Applicability of the general rules to RCBO's functionally dependent on line voltage |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 61008-1:2013 |
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part 1: General rules |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 61008-1:2024 |
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part 1: General rules |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 61008-2-1:2024 |
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB's). Part 2-1: Applicability of the general rules to RCCB's functionally independent of line voltage |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 61008-2-2:2024 |
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB's). Part 2-2: Applicability of the general rules to RCCB's functionally dependent on line voltage |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 60898-1:2019 |
Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations - Part 1: Circuit-breakers for a.c. operation |
순시특성 시험: AC 25 kA & DC 25 kA
과전류특성 시험: AC 1 250 A & DC 1 250 A
단락차단 시험: AC 440 V, 25 kA & DC 440 V, 25 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 125 A & DC 125 A
부하개폐 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A
과부하 시험: AC 440 V, 1 250 A & DC 440 V, 1 250 A |
부속시설-1 |
| IEC 60947-5-1:2016 |
Low-voltage switchgear and controlgear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| IEC 60947-5-1:2024 |
Low-voltage switchgear and controlgear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| IEC 60947-4-1:2018 |
Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| IEC 60947-4-1:2023 |
Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
과전류특성 시험: AC 12 000 A & DC 7 000 A
단락차단 시험: AC 1 000 V, 200 kA & DC 1 500 V, 100 kA
내전압 시험: AC 2 500 V & DC 4 000 V
임펄스 시험: 20 kV
온도상승 시험: AC 12 000 A & DC 7 000 A
부하개폐 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA
과부하 시험: AC 1 000 V, 7 kA & DC 1 500 V, 14 kA |
부속시설-1 |
| SPS-KEMC 1120-0579:2018 |
디지털 보호계전기
(제외 항목)
6.4.1.2 방사방해시험
6.8.2.3 충돌(bump) 시험
6.8.3 지진시험 |
0.1 V∼5 kV,
0.1 A∼1 kA |
소재지 |
| ▶ 대전력, 고전압 기기 |
IEC 60947-3:2020
+AMD1:2025 CSV |
Low-voltage switchgear and controlgear –Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA |
소재지 |
| IEC 61439-1:2020 |
Low-voltage switchgear and controlgear assemblies – Part 1: General rules
(Exception)
10.2.4 Resistance to ultraviolet (UV) radiation |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10 |
소재지 |
| IEC 61439-2:2020 |
Low-voltage switchgear and controlgear assemblies - Part 2: Power switchgear and controlgear assemblies
(Exception)
10.2.4 Resistance to ultraviolet (UV) radiation |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10 |
소재지 |
| IEC 61439-3:2024 |
Low-voltage switchgear and controlgear assemblies –
Part 3: Distribution boards intended to be operated by ordinary persons (DBO)
(Exception)
10.2.4 Resistance to ultraviolet (UV) radiation |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10 |
소재지 |
| IEC 61439-6:2012 |
Low-voltage switchgear and controlgear assemblies - Part 6: Busbar trunking systems (busways)
(Exception)
10.2.4 Resistance to ultraviolet (UV) radiation |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10 |
소재지 |
| IEC TR 61641:2014 |
Enclosed low-voltage switchgear and controlgear assemblies – Guide for testing under conditions of arcing due to internal fault
8 Testing – Arc fault tests |
Max. 100 kV
Max. 200 kA |
소재지 |
| IEC 62271-1:2017 |
High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
(Exception)
7.2.3 Wet tests
7.3 Radio interference voltage (RIV) test
7.2.10 Partial discharge tests
7.9.1.1 Emission tests from the main circuits (radio interference
voltage test, RIV) |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-1:2017 + AMD1:2021 CSV |
High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
(Exception)
7.2.3 Wet tests
7.2.8 Tests of switchgear and controlgear of Ur > 245 kV
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test
7.9.1.1 Emission tests from the main circuits (radio interference
voltage test, RIV) |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-100:2017 |
High-voltage switchgear and controlgear - Part 100: Alternating-current circuit breakers
(Exception)
6.2.2 Wet test procedure
6.2.7 Tests of circuit-breakers of Ur > 245 kV
6.2.8 Artificial pollution tests
6.2.9 Partial discharge tests
6.3 Radio interference voltage (r.i.v.) tests
6.109 Short-line fault tests |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-100:2021 |
High-voltage switchgear and controlgear - Part 100: Alternating-current circuit breakers
(Exception)
7.2.3 Wet test procedure
7.2.8 Tests of switchgear and controlgear of Ur > 245 kV
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test
7.109 Short-line fault tests |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-100:2024 CSV |
High-voltage switchgear and controlgear - Part 100: Alternating-current circuit breakers
(Exception)
7.2.3 Wet test procedure
7.2.8 Tests of switchgear and controlgear of Ur > 245 kV
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test
7.109 Short-line fault tests |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-102:2018 |
High-voltage switchgear and controlgear - Part 102: Alternating current disconnectors and earthing switches
(Exception)
7.2.3 Wet test procedure
7.2.8 Tests of switchgear and controlgear of Ur > 245 kV
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test
7.103 Operation under severe ice conditions |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-102:2022 |
High-voltage switchgear and controlgear - Part 102: Alternating current disconnectors and earthing switches
(Exception)
7.2.3 Wet test procedure
7.2.8 Tests of switchgear and controlgear of Ur > 245 kV
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test
7.103 Operation under severe ice conditions |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-103:2011 |
High-voltage switchgear and controlgear - Part 103: Alternating current switches for rated voltages above 1 kV up to and including 52 kV
(Exception)
6.2.8 Artificial pollution tests for outdoor insulators
6.2.9 Partial discharge tests
6.3 Radio interference voltage (r.i.v.) test
6.102.5 Operation under severe ice conditions |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-103:2021 |
High-voltage switchgear and controlgear - Part 103: Alternating current switches for rated voltages above 1 kV up to and including 52 kV
(Exception)
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test
7.102.5 Operation under severe ice conditions |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-105:2012 |
High-voltage switchgear and controlgear - Part 105: Alternating current switchfuse combinations for rated voltages above 1 kV up to and including 52 kV
(Exception)
6.2.9 Partial discharge tests
6.3 Radio interference voltage (r.i.v.) tests |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-105:2021 |
High-voltage switchgear and controlgear - Part 105: Alternating current switch-fuse combinations for rated voltages above 1 kV up to and including 52 kV
(Exception)
7.3 Radio interference voltage (RIV) test |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-106:2011 |
High-voltage switchgear and controlgear - Part 106: Alternating current contactors, contactor-based controllers and motor-starters
(Exception)
6.2.2 Wet test procedure
6.2.7 Tests of contactors and motor starters of Ur > 245 kV
6.2.8 Artificial pollution tests for outdoor insulators
6.2.9 Partial discharge tests
6.3 Radio interference voltage (r. i.v.) test
6.108 High-voltage motor current switching tests |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-106:2021 |
High-voltage switchgear and controlgear - Part 106: Alternating current contactors, contactor-based controllers and motor-starters
(Exception)
7.109 High-voltage motor current switching tests |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-200:2011 |
High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
(Exception)
6.2.2 Wet test procedure
6.2.7 Tests of switchgear and controlgear of Ur > 245 kV
6.2.8 Artificial pollution tests for outdoor insulators
6.2.9 Partial discharge tests
6.105 Weatherproofing test |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-200:2021 |
High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
(Exception)
7.2.3 Wet test procedure
7.2.8 Tests of switchgear and controlgear of Ur > 245 kV
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-200:2024 |
High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
(Exception)
7.2.3 Wet test procedure
7.2.8 Tests of switchgear and controlgear of Ur > 245 kV
7.2.9 Artificial pollution tests for outdoor insulators
7.2.10 Partial discharge tests
7.3 Radio interference voltage (RIV) test |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 62271-201:2014 |
High-voltage switchgear and controlgear - Part 201: AC solid-insulation enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
(Exception)
6.2.2 Wet test procedure
6.2.7 Tests of switchgear and controlgear of Ur > 245 kV
6.2.8 Artificial pollution tests for outdoor insulators
6.2.9 Partial discharge tests
6.3 Radio interference voltage (r. i.v.) test |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEEE Std C37.09™:2018 |
IEEE Standard Test Procedures for AC High-Voltage Circuit Breakers with Rated Maximum Voltage Above 1000 V
(Exception)
4.5.4.2 Wet tests procedure
4.5.6 Impulse voltage test for interrupters and resistors
4.8.2.5 Short-line fault test conditions
4.11 Inductive load switching |
Max. 100 kV
LI Max. 350 kV,
40 kJ
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEC 60076-5:2006 |
Power transformers –
Part 5: Ability to withstand short circuit |
Max. 100 kV
LI Max. 350 kV,
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| IEEE Std C57.12.91™:2020 |
IEEE Standard Test Code for Dry-Type Distribution and Power Transformers
(Exception)
6. Polarity and phase-relation tests
7. Ratio tests
8. Excitation losses and current
9. Load losses and impedance voltage
10. Dielectric tests
11. Temperature rise test
13. Audible sound-level measurements
14. Mechanical design tests |
Max. 100 kV
LI Max. 350 kV,
1 μΩ ~ 10 mΩ
Max. 200 kA
IP11 ~ IP45
IK07, IK09, IK10
Max. 750 μSv/h |
소재지 |
| ▶ 계측기기 |
| IEC 62052-11:2020 |
Electricity metering equipment - General requirements, tests and test conditions - Part 11: Metering equipment
(Exception)
DC Meters
5.11.2 Optical characteristics
7.11 Time-keeping accuracy
8.3.6 Protection against solar radiation
8.4 Durability
9.3.14 Emission requirements |
±20 kV,
5 mA ∼ 120 A |
소재지 |
| IEC 62052-31:2024 |
Electricity metering equipment – General requirements, tests and test conditions – Part 31: Product safety requirements and tests
(Exception)
DC Meters
9.3.2 Flammability
11. Penetration of dust and water
12. Liberated gases, explosion and implosion – Batteries and battery charging
13. Requirements for components and sub-assemblies
14. Requirements for protection against hazards arising from reasonably foreseeable misuse |
±20 kV,
5 mA ∼ 120 A |
소재지 |
| IEC 62053-11:2016 |
Electricity metering equipment (a.c.) - Particular requirements – Part 11: Electromechanical meters for active energy (classes 0.5, 1 and 2)
(Exception)
classes 0.5 |
±20 kV,
5 mA ∼ 120 A |
소재지 |
| IEC 62053-21:2020 |
Electricity metering equipment - Particular requirements - Part 21: Static meters for AC active energy (classes 0.5, 1 and 2) |
±20 kV,
5 mA ∼ 120 A |
소재지 |
| IEC 62053-23:2020 |
Electricity metering equipment - Particular requirements – Part 23: Static meters for reactive energy (classes 2 and 3) |
±20 kV,
5 mA ∼ 120 A |
소재지 |
| KS C 1214:2010 |
전자식 유효/무효 전력량계
(유효 0.2급/0.5급, 1.0급/2.0급, 무효 2.0급/ 3.0급)
(제외 항목)
유효전력량계 (유효 0.2급)
7.17.2 전자파 장해
7.18.4 태양열 복사
7.18.5 습윤·아황산가스의 영향
7.18.6 염수 분무의 영향
7.18.7 고온·급랭의 영향
7.18.8 옥외 폭로의 영향
7.18.9 금속 재료의 표면처리
7.22 먼지·물의 침투에 대한 보호성
8.9.2 광특성
9. 검사 |
±20 kV,
5 mA ∼ 120 A |
소재지 |
산업통상자원부 고시 제2020-230호
(2020.12.28) |
전력량계 기술기준
제1-1절 전력량계 일반 요구사항
제1-3절 교류 전자식 전력량계 형식승인 기준
(제외 항목)
유효전력량계 (유효 0.2급)
제1-2절 교류 유도형 형식승인 기준
제1-4절 직류 전자식 전력량계 형식승인 기준
8.3.5 태양열복사
9.2.11 전자파 장해
10 소프트웨어 요구사항
12.6 먼지·물의 침투에 대한 보호성
13.1 습윤·아황산가스의 영향
13.2 염수분무의 영향
13.3 고온·급냉의 영향
13.5 금속재료의 표면처리
부속서 H 특수형 전력량계에 대한 평가
부속서 I 외부 계량장치 사용에 대한 영향 시험
고시 내 적용대상 중 “콘센트접속형” |
±20 kV,
5 mA ∼ 120 A |
소재지 |
| ▶ 산업용 전기기기 |
| IEC 61131-2:2017 |
Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests
(Exception)
6.4.5 Digital outputs for alternating currents (positive logic, current sourcing)
6.4.6 Digital outputs for direct current (current sourcing)
6.5.4 Analog temperature inputs
6.5.5 Requirements for analog channel compatibility with HART® (Highway
Addressable Remote Transducer)
6.6 Communication interface requirements
6.7 Main processing unit(s) and memory(ies) requirements
6.8 Remote input/output station (RIOS) requirements
6.9 Peripherals (PADTs, TEs, HMIs) requirements
6.10 Self-tests and diagnostics requirements
7.3.1 Immunity levels, Table 41 – Power-frequency magnetic field immunity test |
전압(AC): Max. 300 V
(DC): Max. 400 V
전류(AC): Max. 8 A
(DC): Max. 30 A
전원 주파수: Max. 950 Hz
온도: (-40 ~ 130) ℃
습도: (20 ~ 95) % R.H.
진동 주파수: Max. 3 000 Hz
충격 가속도: Max. 294 m/s²
ESD: ±30 kV
RS: 80 MHz ~ 1 000 MHz(10V/m),
1.4 GHz ~ 6 GHz(20 V/m)
EFT: ±(0.25 ~ 4) kV
Surge: Level: ±(0.5 ~ 15) kV
CS: 150 kHz ~ 80 MHz(30 V) |
부속시설-2 |
| IEC 61010-2-201:2024 |
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-201: Particular requirements for control equipment
6.8.3.1 The a.c. voltage test
6.8.3.2 The d.c. voltage test
10.3 Other temperature measurements
10.5.2 Non-metallic ENCLOSURES |
전압(AC): Max. 300 V
(DC): Max. 400 V
전류(AC): Max. 8 A
(DC): Max. 30 A
전원 주파수: Max. 950 Hz
온도: (-40 ~ 130) ℃
습도: (20 ~ 95) % R.H.
내전압: Max. 5 kV |
부속시설-2 |
| IEC 61800-5-1:2022 |
Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy
5.2.1 Visual inspection
5.2.2.1 Non-accessibility test
5.2.2.4 Enclosure integrity test
5.2.2.4.3 Impact test
5.2.2.4.4 Drop test
5.2.2.4.5 Mould stress relief distortion test
5.2.3.4 AC or DC voltage test
5.2.3.8 Capacitor discharge test
5.2.3.10 Temperature rise test
5.2.3.12 Input test
5.2.3.14 Test procedure for determination of working voltage
5.2.4.6.4 Electronic motor overload protection test
5.2.4.6.5 Electronic motor thermal memory retention trip test
5.2.4.6.6 Electronic motor thermal memory retention loss of power test
5.2.4.6.7 Electronic motor thermal speed sensitivity test
5.2.4.8 Current limiting test
5.2.4.9 Output overload test
5.2.4.12 Loss of phase test
5.2.4.13 Cooling failure tests
5.2.4.13.2 Inoperative blower motor test
5.2.4.13.3 Clogged filter test
5.2.4.13.4 Loss of coolant test
5.2.6.3.1 Preconditioning or recovery procedure for climatic tests
5.2.6.3.2 Dry heat test (steady state)
5.2.6.3.3 Cold test (steady state)
5.2.6.3.4 Damp heat test (steady state)
5.2.6.4 Vibration test |
전압(AC): Max. 800 V
전류(AC): Max. 1 200 A
온도: (-40 ~ 130) °C
습도: (20 ~ 95) % R.H.
내전압: AC (1 ~ 5) kV
DC (0.05 ~ 5.50) kV
진동 주파수: Max. 3 000 Hz |
부속시설-2 |
| KS C IEC 61131-2:2017 |
산업용 프로세스 측정 및 제어 - 프로그래머블 컨드롤러 - 제2부: 장비 요구사항 및 시험
(제외항목)
6.4.5 교류에 대한 디지털 출력(포지티브 회로, 전류 소싱)
6.4.6 직류 디지털 출력(전류 소싱)
6.5.4 아날로그 온도 입력
6.5.5 HART®와의 아날로그 채널 호환성 요구사항
6.6 통신 인터페이스 요구사항
6.7 주 처리 장비 및 메모리 요구사항
6.8 원격 입력/출력 스테이션(RIOS) 요구사항
6.9 주변장비(PADT, TE, HMI) 요구사항
6.10 자체 시험 및 진단 요구사항
7.3.1 EMC 내성 수준, 표41-전원 주파수 자기장 내성 시험 |
전압(AC): Max. 300 V
(DC): Max. 400 V
전류(AC): Max. 8 A
(DC): Max. 30 A
전원 주파수: Max. 950 Hz
온도: (-40 ~ 130) ℃
습도: (20 ~ 95) % R.H.
진동 주파수: Max. 3 000 Hz
충격 가속도: Max. 294 m/s²
ESD: ±30 kV
RS: 80 MHz ~ 1 000 MHz(10V/m),
1.4 GHz ~ 6 GHz(20 V/m)
EFT: ±(0.25 ~ 4) kV
Surge: Level: ±(0.5 ~ 15) kV
CS: 150 kHz ~ 80 MHz(30 V) |
부속시설-2 |
| ▶ 전자기적합성 |
| CISPR 11:2019 |
Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
(Exception)
8.3 Radiation test site for 9 kHz to 1 GHz
ccc
9 Radiation measurements 1 GHz to 18 GHz |
CE Frequency Range:
150 kHz ∼ 30 MHz |
소재지 |
| CISPR 11:2024 |
Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
(Exception)
8.3 Radiation test site for 9 kHz to 1 GHz
8.4 Alternative radiation test sites for the frequency range 30 MHz to 1 GHz
8.5 FAR for measurements in the range 30 MHz to 1 GHz
9 Radiation measurements 1 GHz to 18 GHz |
CE Frequency Range:
150 kHz ∼ 30 MHz |
소재지 |
| CISPR 11:2019 |
Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
(Exception)
8.4 Alternative radiation test sites for the frequency range 30 MHz to 1 GHz |
CE: 150 kHz ∼ 30 MHz,
RE: 9 kHz ~ 18 GHz |
부속시설-2 |
| CISPR 11:2024 |
Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
(Exception)
8.4 Alternative radiation test sites for the frequency range 30 MHz to 1 GHz
8.5 FAR for measurements in the range 30 MHz to 1 GHz |
CE: 150 kHz ∼ 30 MHz,
RE: 9 kHz ~ 18 GHz |
부속시설-2 |
| CISPR 16-2-1:2017 |
Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements |
Frequency Range:
9 kHz ∼ 30 MHz |
소재지 |
| CISPR 16-2-1:2017 |
Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements |
Frequency Range: 9 kHz ∼ 30 MHz |
부속시설-2 |
| CISPR 16-2-3:2023 |
Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements
(Exception)
7.4 Fully-anechoic room measurements (30 MHz to 1 GHz)
7.7 In situ measurements (9 kHz to 18 GHz)
7.9 Reverberation chamber measurements (80 MHz to 18 GHz)
7.10 TEM waveguide measurements (30 MHz to 18 GHz) |
Frequency Range: 9 kHz ∼ 18 GHz |
부속시설-2 |
| CISPR 32:2019 |
Electromagnetic compatibility of multimedia equipment - Emission requirements
(Exception)
A.2 Requirements for radiated emissions |
CE Frequency Range:
150 kHz ∼ 30 MHz |
소재지 |
| CISPR 32:2019 |
Electromagnetic compatibility of multimedia equipment - Emission requirements
(Exception)
A1.4 (FAR) |
CE: 150 kHz ∼ 30 MHz,
RE: 30 MHz ~ 6 GHz |
부속시설-2 |
| IEC 60255-26:2023 |
Measuring relays and protection equipment - Part 26: Electromagnetic compatibility requirements
(Exception)
7.2.2 Radiated emission |
ESD: ±25 kV,
RS: 80 MHz ∼ 6 GHz (Max. 10 V/m),
EFT: ±4 kV,
Surge: Max. ±4 kV
CS: Max. 10 V
Magnetic Field: Max. 1 000 A/m
Voltage fluctuation rate: (0∼100) % |
소재지 |
| IEC 60255-26:2023 |
Measuring relays and protection equipment - Part 26: Electromagnetic compatibility requirements
7.2.2 Radiated emission |
RE: 30 MHz ~ 6 GHz |
부속시설-2 |
| IEC 61000-3-2:2020 |
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤16 A per phase) |
Current:
Max. 16 A |
소재지 |
| IEC 61000-3-2:2024 |
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤16 A per phase) |
Current:
Max. 16 A |
소재지 |
| IEC 61000-3-12:2021 |
Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16 A and ≤ 75 A per phase |
Current:
Max. 75 A |
소재지 |
| IEC 61000-4-2:2008 |
Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
Voltage: Max. ±30 kV |
소재지 |
| IEC 61000-4-2:2008 |
Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
Voltage: Max. ±30 kV |
부속시설-2 |
| IEC 61000-4-2:2025 |
Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
Voltage: Max. ±30 kV |
소재지 |
| IEC 61000-4-2:2025 |
Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
Voltage: Max. ±30 kV |
부속시설-2 |
| IEC 61000-4-3:2020 |
Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
Frequency:
80 MHz ∼ 6 GHz
Electric field strength:
Max. 30 V/m |
소재지 |
| IEC 61000-4-3:2020 |
Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
Frequency: 80 MHz ∼ 6 GHz,
Electric field strength: Max. 20 V/m |
부속시설-2 |
| IEC 61000-4-4:2012 |
Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
Voltage:
Max. ±4 kV |
소재지 |
| IEC 61000-4-4:2012 |
Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
Voltage:
Max. ±4 kV |
부속시설-2 |
| IEC 61000-4-5:2017 |
Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test |
Voltage:
Max. ±10 kV |
소재지 |
| IEC 61000-4-5:2017 |
Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test |
Voltage:
Max. ±15 kV |
부속시설-2 |
| IEC 61000-4-6:2013 |
Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
Frequency range:
150 kHz ∼ 230 MHz
Voltage:
Max. 30 V |
소재지 |
| IEC 61000-4-6:2013 |
Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
Frequency range: 150 kHz ∼ 230 MHz,
Voltage: Max. 30 V |
부속시설-2 |
| IEC 61000-4-6:2023 |
Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
Frequency range: 150 kHz ∼ 230 MHz,
Voltage: Max. 30 V |
소재지 |
| IEC 61000-4-6:2023 |
Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
Frequency range: 150 kHz ∼ 230 MHz,
Voltage: Max. 30 V |
부속시설-2 |
| IEC 61000-4-8:2009 |
Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test |
Magnetic field strength:
Max. 1 000 A/m |
소재지 |
| IEC 61000-4-11:2020 |
Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with input current up to 16 A per phase |
Voltage fluctuation rate:
(0 ∼ 100) % |
소재지 |
| IEC 61000-4-12:2017 |
Electromagnetic compatibility (EMC) - Part 4-12: Testing and measurement techniques - Ring wave immunity test |
Voltage:
Max. ±6.6 kV |
소재지 |
| IEC 61000-4-16:2015 |
Electromagnetic compatibility (EMC) - Part 4-16: Testing and measurement techniques - Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 kHz |
Max. 300 V(DC ~ 60 Hz)
Max 30 V(15 Hz ~ 150 kHz) |
소재지 |
| IEC 61000-4-17:2008 |
Electromagnetic compatibility (EMC) - Part 4-17: Testing and measurement techniques - Ripple on d.c. input power port immunity test |
Max 15 %(50 Hz ~ 360 Hz) |
소재지 |
| IEC 61000-4-18:2019 |
Electromagnetic compatibility (EMC) - Part 4-18: Testing and measurement techniques - Damped oscillatory wave immunity test |
Voltage:
Max. ±4 kV
Frequency:
100 kHz
(1, 3, 10, 30) MHz |
소재지 |
| IEC 61000-4-29:2000 |
Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
Voltage fluctuation rate:
(0 ∼ 120) % |
소재지 |
| IEC 61000-6-1:2016 |
Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (3 V/m),
EFT: Max. ±1 kV,
Surge: Max. ±2 kV
CS: 3 V
Magnetic Field: 3 A/m
Voltage fluctuation rate: (0 ∼ 100) % |
소재지 |
| IEC 61000-6-1:2016 |
Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (3 V/m),
EFT: Max. ±1 kV,
Surge: Max. ±2 kV,
CS: 3 V |
부속시설-2 |
| IEC 61000-6-2:2016 |
Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (10 V/m),
EFT: Max. ±2 kV,
Surge: Max. ±2 kV
CS: 10 V
Magnetic Field: ~30 A/m
Voltage fluctuation rate: (0 ∼ 100) % |
소재지 |
| IEC 61000-6-2:2016 |
Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (10 V/m),
EFT: Max. ±2 kV,
Surge: Max. ±2 kV,
CS: 10 V |
부속시설-2 |
| IEC 61000-6-3:2020 |
Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for equipment in residential environments
(Exception)
radiated emissions |
CE Frequency Range:
150 kHz ∼ 30 MHz |
소재지 |
| IEC 61000-6-3:2020 |
Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for equipment in residential environments |
CE: 150 kHz ∼ 30 MHz,
RE: 9 kHz ~ 6 GHz |
부속시설-2 |
| IEC 61000-6-4:2018 |
Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments
(Exception)
Enclosure port |
CE Frequency Range:
150 kHz ∼ 30 MHz |
소재지 |
| IEC 61000-6-4:2018 |
Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments |
CE: 150 kHz ∼ 30 MHz,
RE: 9 kHz ~ 6 GHz |
부속시설-2 |
| IEC 61000-6-5:2015 |
Electromagnetic compatibility (EMC) - Part 6-5: Generic standards - Immunity for equipment used in power station and substation environment |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (Max. 10 V/m),
EFT: Max. ±4 kV,
Surge: Max. ±2 kV,
CS: 10 V,
Magnetic Field: ∼1 000 A/m,
Voltage fluctuation rate: (0 ∼ 100) %,
Main frequency voltage: Max. 300 V,
Common mode disturbances: 15 Hz ∼ 150 kHz(10 V),
Damped Oscillatory wave: (0.1, 1, 3, 10, 30) MHz, Max. 2.5 kV,
Ripple: Max 15 %(50 Hz ~ 360 Hz) |
소재지 |
| IEC 61000-6-5:2015 |
Electromagnetic compatibility (EMC) - Part 6-5: Generic standards - Immunity for equipment used in power station and substation environment |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (Max. 10 V/m),
EFT: Max. ±4 kV,
Surge: Max. ±2 kV,
CS: 10 V |
부속시설-2 |
| IEC 61000-6-8:2020 |
Electromagnetic compatibility (EMC) - Part 6-8: Generic standards - Emission standard for professional equipment in commercial and light-industrial locations
(Exception)
radiated emissions |
CE Frequency Range:
150 kHz ∼ 30 MHz |
소재지 |
| IEC 61000-6-8:2020 |
Electromagnetic compatibility (EMC) - Part 6-8: Generic standards - Emission standard for professional equipment in commercial and light-industrial locations |
CE: 150 kHz ∼ 30 MHz,
RE: 9 kHz ~ 6 GHz |
부속시설-2 |
| IEC 61131-2:2017 |
Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests |
Power frequency magnetic fields: 50/60 Hz, 30 A/m,
Damped Oscillatory wave: 1 MHz, Max. 2.5 kV
Voltage fluctuation rate: (0 ∼ 100) % |
소재지 |
| IEC 61131-2:2017 |
Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests
(Exception)
Power frequency magnetic fields
Damped oscillatory wave |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (Max. 10 V/m),
EFT: Max. ±2 kV,
Surge: Max. ±2 kV,
CS: 10 V,
CE: 150 kHz ∼ 30 MHz,
RE: 9 kHz ~ 6 GHz |
부속시설-2 |
| IEC 61800-3:2022 |
Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods for PDS and machine tools |
Flicker: 16 A
Harmonics emission: Max. 75 A
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (Max. 10 V/m),
EFT: Max. ±2 kV,
Surge: Max. ±2 kV,
CS: 10 V,
CE: 150 kHz ∼ 30 MHz,
Harmonic immunity: Max. 39th,
Voltage fluctuation rate: (0 ∼ 100) %,
Frequency variations: ±4 %,
Voltage unbalance: ±3 % |
소재지 |
| IEC 61800-3:2022 |
Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods for PDS and machine tools
(Exception)
Flicker
Harmonic emission
Harmonic immunity
Voltage fluctuation
Frequency variations
Voltage unbalance |
ESD: Max. ±8 kV,
RS: 80 MHz ∼ 6 GHz (Max. 10 V/m),
EFT: Max. ±2 kV,
Surge: Max. ±2 kV,
CS: 10 V,
CE: 150 kHz ∼ 30 MHz,
RE: 30 MHz ~ 6 GHz |
부속시설-2 |
| IEEE C37.90.1:2012 |
IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus |
EFT:
Max. ±4 kV,
Oscillatory:
Max. ±2.5 kV |
소재지 |
| IEEE C37.90.1:2012 |
IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus |
EFT: Max. ±4 kV |
부속시설-2 |
| IEEE C37.90.1:2024 |
IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus |
EFT: Max. ±4 kV,
Oscillatory: Max. ±2.5 kV |
소재지 |
| IEEE C37.90.1:2024 |
IEEE Standard for Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus |
EFT: Max. ±4 kV |
부속시설-2 |
| IEEE C37.90.2:2004 |
IEEE Standard for Withstand Capability of Relay Systems to Radiated Electromagnetic Interference from Transceivers |
Frequency Range:
80 MHz ∼ 1 GHz (Max. 20 V/m) |
소재지 |
| IEEE C37.90.2:2004 |
IEEE Standard for Withstand Capability of Relay Systems to Radiated Electromagnetic Interference from Transceivers |
Frequency Range: 80 MHz ∼ 1 GHz (Max. 20 V/m) |
부속시설-2 |
| IEEE C37.90.2:2024 |
IEEE Standard for Withstand Capability of Relay Systems to Radiated Electromagnetic Interference from Transceivers |
Frequency Range: 80 MHz ∼ 6 GHz (Max. 20 V/m) |
소재지 |
| IEEE C37.90.2:2024 |
IEEE Standard for Withstand Capability of Relay Systems to Radiated Electromagnetic Interference from Transceivers |
Frequency Range: 80 MHz ∼ 6 GHz (Max. 20 V/m) |
부속시설-2 |
| IEEE C37.90.3:2001 |
IEEE Standard Electrostatic Discharge Tests for Protective Relays |
Voltage:
Max. ±15 kV |
소재지 |
| IEEE C37.90.3:2001 |
IEEE Standard Electrostatic Discharge Tests for Protective Relays |
Voltage: Max. ±15 kV |
부속시설-2 |
| IEEE C37.90.3:2023 |
IEEE Standard Electrostatic Discharge Tests for Protective Relays |
Voltage:
Max. ±15 kV |
소재지 |
| IEEE C37.90.3:2023 |
IEEE Standard Electrostatic Discharge Tests for Protective Relays |
Voltage: Max. ±15 kV |
부속시설-2 |
| ▶ 환경 및 신뢰성 |
| IEC 60068-2-1:2025 |
Environmental testing - Part 2-1: Tests - Test A: Cold |
(-50 ∼ 0) ℃ |
소재지 |
| IEC 60068-2-2:2025 |
Environmental testing - Part 2-2: Tests - Test B: Dry heat |
(0 ∼ 180) ℃ |
소재지 |
| IEC 60068-2-6:2007 |
Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
(5 ∼ 2 000) Hz,
(1 ∼ 490) m/s² |
소재지 |
| IEC 60068-2-14:2023 |
Environmental testing - Part 2-14: Tests. Test N: Change of temperature
(Exception)
9 Test Nc: Rapid change of temperature, two-fluid-bath method |
(-50 ∼ 180) ℃ |
소재지 |
| IEC 60068-2-27:2008 |
Environmental testing. Part 2-27: Tests. Test Ea and guidance: Shock
(Exception)
Fig.2 final-peak saw-tooth pulse shapes
Fig.3 trapezoidal pulse shapes |
(1 ∼ 490) m/s² |
소재지 |
| IEC 60068-2-30:2025 |
Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
(20 ∼ 95) % R.H.
(20 ∼ 98) ℃ |
소재지 |
| IEC 60695-2-10:2013 |
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
(550 ∼ 960) ℃ |
소재지 |
| IEC 60695-2-10:2021 |
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
(550 ∼ 960) ℃ |
소재지 |
| IEC 60695-2-11:2014 |
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
(550 ∼ 960) ℃ |
소재지 |
| IEC 60695-2-11:2021 |
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
(550 ∼ 960) ℃ |
소재지 |
| IEC 60068-2-1:2025 |
Environmental testing - Part 2-1: Tests - Test A: Cold
(Exception)
5.3 Test Ad: Cold for heat-dissipating specimens with gradual change of temperature
that are powered after initial temperature stabilization
5.4 Test Ae: Cold for heat-dissipating specimens with gradual change of temperature
that are required to be powered throughout the test |
(-50 ∼ 0) ℃ |
부속시설-2 |
| IEC 60068-2-2:2025 |
Environmental testing - Part 2-2: Tests - Test B: Dry heat
(Exception)
5.3 Test Bd: Dry heat for heat-dissipating specimens with gradual change of
temperature that are not powered during the conditioning period
5.4 Test Be: Dry heat for heat-dissipating specimens with gradual change of
temperature that are required to be powered throughout the test |
(0 ∼ 180) ℃ |
부속시설-2 |
| IEC 60068-2-14:2023 |
Environmental testing - Part 2-14: Tests. Test N: Change of temperature
(Exception)
9 Test Nc: Rapid change of temperature, two-fluid-bath method |
(-50 ∼ 180) ℃ |
부속시설-2 |
| IEC 60068-2-30:2025 |
Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
(20 ∼ 95) % R.H.
(20 ∼ 98) ℃ |
부속시설-2 |
| IEC 60068-2-11:1981 |
Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
Temperature: (35 ± 2) ℃
Salt(NaCl) concentration: (5 ± 1) %
pH: 6.5 ~ 7.2
Average collection rate: (1.0 ~ 2.0) mL/h |
소재지 |
| IEC 60068-2-11:2021 |
Environmental testing - Part 2-11: Tests - Test Ka: Salt mist |
Temperature: (35 ± 2) ℃
Salt(NaCl) concentration: (50 ± 5) g/L
pH: 6.5 ~ 7.2
Average collection rate: (1.5 ± 0.5) mL/h |
소재지 |
| IEC 60068-2-52:2017 |
Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution)
(Exception)
9.4.9 Test method 8 |
Temperature: (23 ~ 60) ℃
Humidity: (30 ~ 95) % R.H.
Salt(NaCl) concentration: (50 ± 5) g/L
pH: 6.5 ~ 7.2
Average collection rate: (1.5 ± 0.5) mL/h |
소재지 |
| KS C IEC 60068-2-11:2021 |
환경 시험 - 제2-11부: 시험 - 시험 Ka: 염수분무 |
온도: (35 ± 2) ℃
염화소듐의 농도: (50 ± 5) g/L
pH: 6.5 ~ 7.2
평균수집률: (1.5 ± 0.5) mL/h |
소재지 |
| KS C IEC 60068-2-52:2017 |
환경 시험 - 제2-52부: 시험 - Kb: 염수분무, 사이클(염화소듐 용액)
(제외)
9.4.9 시험방법 8 |
온도: (23 ~ 60) ℃
상대습도: (30 ~ 95) % R.H.
염화소듐의 농도: (50 ± 5) g/L
pH: 6.5 ~ 7.2
평균수집률: (1.5 ± 0.5) mL/h |
소재지 |
| KS D 9502:2024 |
염수 분무 시험방법(중성, 아세트산 및 캐스분무 시험)
(제외)
아세트산 및 캐스분무 시험 |
온도: (35 ± 2) ℃
염화소듐의 농도: (50 ± 5) g/L
pH: 6.5 ~ 7.2
평균수집률: (1.5 ± 0.5) mL/h |
소재지 |
